================= Required Hardware ================= HW preparation ================= • VisionFive 2 • Micro-SD card (32 GB or more) • Micro-SD card reader • PC with Linux/windows • USB to Serial Converter (FT232RL) • Power adapter(5V 3A) • USB Type-C cable .. list-table:: :widths: 50 50 :align: left :header-rows: 0 * - .. image:: res/vf2.jpg :alt: VisionFive 2 Board :width: 300px - .. image:: res/ft232.jpg :alt: FT232 USB to UART :width: 300px Using a USB to Serial Converter =============================== .. image:: res/uart_wiring.jpg :alt: usb uart uart_wiring :width: 500px Connect to the serial device by typing the following command .. code-block:: bash sudo picocom -b 115200 /dev/ttyUSB0 Sample serial output .. code-block:: console StarFive # U-Boot SPL 2021.10 (Feb 12 2023 - 18:15:33 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.2 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : StarFive VisionFive V2 Platform Features : medeleg Platform HART Count : 5 Platform IPI Device : aclint-mswi Platform Timer Device : aclint-mtimer @ 4000000Hz Platform Console Device : uart8250 Platform HSM Device : jh7110-hsm Platform PMU Device : --- Platform Reboot Device : pm-reset Platform Shutdown Device : pm-reset Firmware Base : 0x40000000 Firmware Size : 292 KB Runtime SBI Version : 1.0 Domain0 Name : root Domain0 Boot HART : 1 Domain0 HARTs : 0*,1*,2*,3*,4* Domain0 Region00 : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01 : 0x0000000040000000-0x000000004007ffff () Domain0 Region02 : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address : 0x0000000040200000 Domain0 Next Arg1 : 0x0000000042200000 Domain0 Next Mode : S-mode Domain0 SysReset : yes Boot HART ID : 1 Boot HART Domain : root Boot HART Priv Version : v1.11 Boot HART Base ISA : rv64imafdcbx Boot HART ISA Extensions : none Boot HART PMP Count : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count : 2 Boot HART MIDELEG : 0x0000000000000222 Boot HART MEDELEG : 0x000000000000b109 U-Boot 2021.10 (Feb 12 2023 - 18:15:33 +0800), Build: jenkins-VF2_515_Branch_SDK_Release-24 CPU: rv64imacu Model: StarFive VisionFive V2 DRAM: 4 GiB MMC: sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB OK StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : StarFive Technology Co., Ltd. Product full SN: VF7110B1-2253-D004E000-40000984 data version: 0x2 PCB revision: 0xb2 BOM revision: A Ethernet MAC0 address: 6c:cf:39:00:6e:30 Ethernet MAC1 address: 6c:cf:39:00:6e:31 --------EEPROM INFO-------- In: serial@10000000 Out: serial@10000000 Err: serial@10000000 Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 399 bytes read in 4 ms (96.7 KiB/s) Importing environment from mmc1 ... Can't set block device Hit any key to stop autoboot: 0 Can't set block device libfdt fdt_check_header(): FDT_ERR_BADMAGIC Retrieving file: /boot/extlinux/extlinux.conf Can't set block device Error reading config file StarFive #